X-09 Type 1F (High Security Electronic Lock) Operating Instructions

VIP免费

2024-11-29 0 0 489.21KB 20 页 5.9玖币

侵权投诉

OPERATING

INSTRUCTIONS

X-09TM

Type 1F

HIGH SECURITY ELECTRONIC LOCK

TABLE OF CONTENTS

INTRODUCTION ..............................................................................1

Lock On Back Cover .......................................................................1

DIALING THE X-09........................................................................2

Dialing Methods ...............................................................................2

To Power the Lock ..........................................................................2

Dialing A Combination .....................................................................2

OPEN AND CLOSE THE X-09 (FACTORY COMBINATION) ......................4

To Open the Lock (Using the Factory Combination) ......................4

To Close the Lock ...........................................................................4

X-09 LOCK SETUP .......................................................................5

Set Operating Mode and Change Combinations ............................5

If You Lock the Change Key in the Safe ........................................8

USING THE X-09..........................................................................9

Single Combination Mode ...............................................................9

Dual Combination Mode ................................................................ 9

Supervisory/Subordinate Mode .....................................................10

Correct Method of Closing/Relocking Container...........................11

AUDIT FEATURES OF THE LOCK .....................................................12

To Check the Number of Successful Openings ........................... 12

To Check the Number of Unsuccessful Attempts........................12

GUIDE TO SYMBOLS ...................................................................13

For Technical Support

Call: 1-800-950-4744

INTRODUCTION

The X-09 uses sophisticated computer security and makes dialing much easier than that of

traditional combination locks. The microprocessor in the lock recognizes a number as part of a

combination when you change dialing direction. (See the section on Dialing the X-09.)

Note:

The lock is shipped preset to operate in the Single Combination Mode with a

Default Factory Combination of 50-25-50.

LOCK ON BACK COVER

The Lock On Back Cover (LOBC) feature provides a locking mechanism that locks the back

cover in place after installation. The design is such that the back cover cannot be removed

without visible damage unless the combination is known, regardless of whether the lock is locked

or unlocked.

Note:

Because of the LOBC feature, it is not an easy task to remove the back

cover to read the lock serial number after the lock is installed. Since you may

need the serial number of the lock to reset it if the combination is lost or

forgotten, it is important that you keep a record of the lock serial number in a

secure place. If you do not have the serial number, follow the procedure below

to remove the back cover and retrieve the serial number.

To Remove the Lock on Back Cover:

1. Dial the combination(s) to open the lock and

then retract the bolt.

2. Release the container locking bolts.

3. Open the container.

4. Remove the dust cover plate.

5. Locate the lock on back cover pin on the back

cover of the lock case. (See Figure 1.)

6. Turn the dial to the left to extend the bolt. Do

not close the container.

7. Dial the combination(s) to open the lock.

8. Before turning the dial to retract the

bolt, pull out on the unlocking button.

9. While holding the button out, turn the

dial to the right to retract the bolt to

the unlocked position.

10. Remove the back cover screws.

11. Remove the back cover assembly.

12. Look at the label on the large

capacitor on the system card to get

the lock serial number. (See Figure

2.)

Serial

Number

Figure 2 - Serial # on Label on Capacitor

Figure 1 - Lock On Back Cover

Lock On Back

Cover Pin

DIALING THE X-09

DIALING METHODS

The user should dial with complete, full wrist turns. Stopping to regrip produces pauses in dialing

activity. This helps the X-09 distinguish between human and robotic dialers.

Note:

The viewing angle of the LCD is restricted from either side as a security

feature of the lock. This feature restricts viewing of combination dialing by the casual

observer. The display may also appear slightly more dim than previous versions of the

X-xx lock.

TO POWER THE LOCK

You should dial to the left (CounterClockWise) to “power” the lock unless otherwise

instructed for a specific operation. It usually requires 5-10 turns of the dial to

generate sufficient power for lock operations. The lock is considered to be “pow-

ered” as soon as something (number, letter, symbol) appears on the display.

Note:

While the lock is powered, you will notice that the intensity level of the LCD will

vary. The display may appear to become brighter or more dim at different points in

operation. The variations in the display occur due to a security feature of the lock and

should not be of concern to the user.

When you dial to power the lock, it will first display any error conditions that exist on the lock.

If you continue to dial left and if the number of consecutive unsuccessful attempts is three or

more, the unsuccessful attempts count will be displayed along with a lightning bolt. You must slow

down or stop dialing to pause and view the count. The count will disappear when you dial left to

resume operations or when the lock powers down.

DIALING A COMBINATION

The X-09 recognizes a number as being part of a combination when you stop dialing on that

number and then reverse dialing directions. When dialing a combination, you will dial left for the

1st two digits of the combination, dial right for the second two digits, and then dial left

again for the last two digits. When dialing to the left, the numbers will be displayed in an

increasing fashion as you dial. When dialing to the right, the numbers will be displayed in a

decreasing fashion.

Note:

If at any time the dial remains stationary for more than 40 seconds, the lock

will power down (LCD will go blank), requiring the operator to redial the entire combination.

Once the combination has been dialed correctly, you must dial briskly to the right to get an OP

(OPen right) display and to retract the bolt.

Note:

If an incorrect combination is dialed or if the elapsed dialing time of the

combination is less than 10 seconds, a lightning bolt will appear when you dial right to

retract the bolt.

If You Pass Your Target Number When Dialing:

Example A: Target Number = 25.

If you pass your target number by 4 or more, continue dialing until you reach the target

number again.

Example B: Target Number = 25.

If you pass the target number by no more than 3 numbers, you may continue dialing until

you reach the target number as in Example A.

An alternative method is to reverse direction slowly and the display will “jump back” 4

numbers. Then you should dial slowly in the original dialing direction for this target number

until you reach the correct number.

Redial Entire Combination If:

A. The screen goes blank before the lock bolt is retracted.

B. A lightning bolt is displayed.

Caution:

An X-09 lock will initiate a timed lockout of 3 minutes when ten

consecutive wrong combinations have been dialed. Each additional unsuccessful

attempt to open the lock will initiate another timed lockout. If the number of

consecutive unsuccessful attempts reaches fifteen, the timed lockout increases

to 4 minutes. The lockout period is only timed while the lock is powered. To

keep the lock powered until the timed lockout has expired, turn the dial every 30

seconds. A successful opening resets the error count.

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

5.9 玖币 0人已下载

立即下载 VIP免费下载

摘要：

OPERATINGINSTRUCTIONSX-09TMType1FHIGHSECURITYELECTRONICLOCKTABLEOFCONTENTSINTRODUCTION..............................................................................1LockOnBackCover.......................................................................1DIALINGTHEX-09.....................................

展开>> 收起<<

X-09 Type 1F (High Security Electronic Lock) Operating Instructions.pdf

共20页,预览5页

还剩页未读，继续阅读

声明：本站为文档C2C交易模式，即用户上传的文档直接被用户下载，本站只是中间服务平台，本站所有文档下载所得的收益归上传人(含作者)所有。玖贝云文库仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私，请立即通知玖贝云文库，我们立即给予删除！

X-09 Type 1F (High Security Electronic Lock) Operating Instructions

相关推荐

开通VIP享超值会员特权

作者详情

相关内容

热门标签

举报选择: